TP-Link AV2000 Powerline Ethernet Adapter TL-PA9020P KIT - Powerline Network Adapter w/ Passthrough, Noise Filter, 2x2 MIMO, 2 Gigabit Ports, Ethernet Over Power, Plug Pair & Play, Power Saving Mode

I had my doubts but these really work. One in my home and the other in my detached garage. My electric go's underground from my home to the detached garage. All I can say is amazing. The total time was about 15 min. Then hooked up my router and then ran a cable the TV. ... Done and it was amazing. You'll love it.

My apartment has cable service, but the router for my unit was placed in a really odd spot, and the wireless service is pretty bad. SO I remembered powerline units were available, got these as they were highly rated overly on various sites.I was able to turn off wireless on my unit's router, ran a cable from the router to the first unit, set up the second unit on an outlet that appears to be one of the last stops in the electrical circuit, then ran a cable to my own router, which let me run ethernet cables to various devices -- laptops, gaming consoles-- in my office. Definitely beefed up the speed, so little to no buffering.I've reconfigured the networks at times in the apartment, has always worked just fine.Because of one of these rearrangements, I discovered just how bad one of my gaming consoles was running over wireless. My roommate uses that one mainly, doesn't really seem to care. Anyway, I wanted to see if I could use another set of adapters to hook that console up to my personal network through the electrical circuit, too.One set would go from the unit router to my personal router, and the other set would go from my personal router to that gaming console and a couple other devices in the same area.It initially didn't work because the new adapters hooked up to the network for my unit. What I had to do was isolate each network and set them up separately. I unplugged the unit adapters, reset my network's adapters, then set them up on my personal network. Then I plugged the unit's adapters back in, and the two networks both used the electrical circuit individually as desired. Hopefully that saves someone some hassle for that particular scenario.And the target gaming console runs great now.

I recently got this TP-link after my other one had kicked the gutter randomly a while ago, and I got to say, it works great! The power saving mode confused me at first, but I figured it out pretty quickly.They also come with 2 ethernet cables, a bit short might I add but it’s a welcomed surprise.My biggest issue with these however, is the size. My old links were a bit small, so I could put them in a few more tight spaces, but these ars much bigger, most likely to compensate for the power that they output in outlets. It’s not that big of a deal, considering they have an outlet on themselves, which is extremely useful.Pros:• Easy to set up & use• Excellent speeds• Great for video streaming & Gaming• Fair priceCons:• Size is a little bit big• Depending on outlet placement, it could take the whole outlet (although there are workarounds for this, like using a drop cord).

Works extremely well, and I have the router about 40 ft from my TV. Signal goes from 300 mbps to 100, but that's plenty of bandwidth for even 4K. When I lose power, it boots right up, and I don't have to do anything manually-a big plus.

(updated review) 2nd day ownership update:These powerline adaptors completely wiped out my TP-Link Archer C9 router. No joke.I've owned the C9 since Sept 2015 (two months shy of three years), and it has been near perfect. Throughout all of this powerlined adaptor testing I haven't touched my C9 one bit (acting as a simple AP). About an hour after plugging the pair of these powerline adaptors in (one a floor below C9, one a floor above it), slowly but surely all my 2.4, then 5.0G devices drop out. My smart plugs stop responding, Alexa's stop responding, my nest looses its connection... I just noticed my freaking nest rebooted a minute ago for no reason. All the while the powerline adaptors chug along while I perform testing throughout the house. After I unplug the powerline adaptors I have to cold cycle the C9 - it will last anywhere from a few hours to a day at best now before doing the same thing, dropping all my devices. During this if I jack into the ethernet port on the back of the C9 (essentially acting as a switch), I can ping it, get an IP address from my other DHCP server, and connect outbound through my gateway, but NO WIFI. SSIDs are being broadcast, but even if I manually assign an IP I cannot seemingly get any packet movement through the router (have not verified with wireshark). The powerline adaptors seem to directly affect the radios, or power supplies (see below) in this router. I've been setting up and debugging home, corporate and industrial networks as an EE for 15 years, so this is not new to me.If I had messed with the C9's cabling, configuration, power cycled the C9, even moved it prior to testing these adaptors, well I would give these the benefit of doubt and say I inadvertently did something to screw it up. But it was working 100% for months up until now (installed after a move) - and going on three years prior. If it's a coincidence, well I'm sorry to make assumtions, but I'm just putting it out there.I load tested my original C9 12V power adaptor at 3amps for 15-20minutes, and it works as expected. Out of curiousity I plugged a powerline adaptor in and scoped the loaded adaptor 12V output: as expected the powerline adaptors are injecting nearly 800mV of high frequency noise *through* the AC adaptor. This noise shows up at the output of the AC adaptor, every 35mS, for about 400uS in duration and yep, directly into the router. This wasn't even transmitting between adaptors, just an apparent preamble and payload, likely broadcasting for other node discovery. Granted this is the case with any powerline adaptor, however this noise, depending on the frequency, could easily throw switching mode regulator out of whack... If not the AC adaptor itself (I didn't note if this was a linear or switching, but I have to assume switching to get 3.3A@12V), then quite easily any downstream electronics (the C9 no exception) will face issues (with any powerline adaptor).After seeing and experiencing this first hand I am absolutely avoiding powerline adaptors. Do yourself a favor and make due with WiFi.(original review) 1st day ownership:My setup is as follows:1st floor: internet and gateway/router, NAS.2nd floor: cat5 from 1st floor to Archer C9 acting as access point.3rd floor: needed hardwired connection for various office devices (printers, etc).Speed results:1)with units biggybacked, (one plugged into the other):-TPlinkUtil showed 997Mbps (124MBps). File transfer from NAS 328Mbps (41MBps)-wifi NAS transfer 376Mbps (47MBps)2)with one unit on 1st floor, the other on 2nd floor at three different sockets (kitchen/dining/living):-TplinkUtil showed 150-229Mbps (19-29MBps). File transfer from NAS 120-146Mbps (15-17MBps)-wifi NAS transfer (5G AC) 528Mbps (66MBps)3)with one unit on 1st floor, the other on 3rd floor at various sockets (office, bedroom):-TplinkUtil showed 34-79Mbps (4-10MBps). File transfer from NAS up to 96Mbps (12MBps)-wifi NAS transfer 184Mbps (23MBps).Clearly there is very little benefit over a wifi adaptor for using these adaptors, in my setup anyway. A cheap no-name 300N USB adaptor was able to get me the same speeds.Lastly, if browsing the web and doing speedtest tests are all you need, maybe you'll be fine.One note: realize that in most US households the 220 service is broken into two separate 120 "legs". Where the circuit breaker is physically installed inside the electrical panel dictates which leg it's on (often it alternates between one leg and the other when viewing the breakers vertically). To get full performance out of a (any) powerline adapter you *must* be on the same leg as the other adapter(s). Yes they share a neutral and ground but to get the benefit of the "MIMO" you need the other leg also.