Eagle Health Supplies Tub-Mount Sliding Shower Chair Tub Transfer Bench with Swivel Seat, FSA/HSA Eligible, Height Adjustable Shower Seat, Space-Saving Shower Bench for Elderly and Disabled, 77762

Worked perfectly for my Mom, it is helping her get in and out of the tub shower by herself.

Works really well and easy to assemble

My wife is bedridden. I have to use a lift to get her out of bed on onto the seat. Once she is on the lift and belted in, I rotate the seat 90 degrees so she will be facing the wall of the shower with the shower head. Then I release the seat and slide her across to the other side where she is under the shower head. Why five stars when it is "almost" perfect? The way it would be perfect for us is if it were 54 or even 60 inches. In order to put her on the seat, the side outside the shower must be further out that an able bodied person would need. Thus she is sort of off to the side of the shower head. Assembly was easy. Good materials, Packaged well. Would definitely buy again if needed. I have and continue to tell others this is a GREAT product.

It worked well after it was installed. I would have given it 5 stars but even though I measured my tub it didn’t quite fit. I had to add a piece of wood to the outside of the tub and buy a longer screw to install it. Then it worked. Using this was safer than having my 90 year old mother stepping into a bathtub. She just sat on the chair and then we helped her turn the chair while lifting her legs into the tub. Then she would grab the rail and pull the seat across.

This is an exceptionally well-made assistive device -- perfect for my current situation with a broken right leg -- and well worth the money spent. There are only 8 parts to assemble without any tools whatsoever, and lying in bed, I was able to put it together in just over 5 minutes. It took my wife about the same amount of time to take it to the bathroom and mount it on the tub. The clamp mechanism securely fastens the bench to the tub.I weigh about 270 pounds, and the only challenge this presents is that when tranferring from the inside position to the outside position, the seat contacts the clamp, and I have to sort of raise up off the seat and pull the seat forward to get it to lock into position. Without locking, it's a bit unsafe because the seat slides effortlessly along the rails, and standing without being locked causes the seat to slide back into the tub. Other than that I have no real complaints.The seat is wide enough to fit me, which makes it very comforable (I don't need the seat belt, so I removed it) -- the seat back does not have holes as shown in the photo. After using it three or four times now, however, I would strongly recommend ordering one or two of the arm rests for this chair (mine will be coming in several more days). There is a certain amount of security that is provided by being able to push up to a standing position (I am on strict orders for "no weight bearing" on my right leg for at least 4-5 more weeks -- it is exactly four weeks since my accident and surgery on Feb 1/3 2017).The original shipment from Amazon was the wrong item (mismarked box was actually 77662 -- no clamp). The manufacturer happens to be only 20 minutes from my home, and after a little negotiation, they exchanged it for the right bench. Amazon customer support was not helpful at all in this regard -- recommending that I reorder and return the one I received for a refund, which might not have solved the problem of receiving another mismarked box.FYI -- the manufacturer recommends lubricating the sliding raills with WD-40 to maintain the ease of transfer.(March 4) ** After using the bench several days, I discovered the accessory arm rests (#75003) as a separate item. Although my tub has a hand rail installed, it is of little value when attempting to get into or out of the chair, because it is not adjacent to where the seat is. I ordered a pair and will install them today. This should increase the ease of getting into and out of the chair from/to my walker -- having something to grab/push up on. The manufacturer suggests using only one on the side opposite where the leg brace is, and I'll update this with my experience in the next day or two.(March 4) UPDATE on the arm rests: they are very heavy duty, easily installed with two stainless steel carriage bolts and large knobs with brass threaded inserts. I was able to do this while seated in my wheelchair. [BTW, mine arrived in just one day, drop-shipped from the manufacturer to me, instead of from the seller in Florida]There is absolutely **no reason** why both arm rests cannot be installed (no need to grab the leg bracket to slide the seat to the inside position). There is ample clearance between the arm rest and the leg bracket, allowing the seat to rotated 360 degrees in all positions. Only if a person's body is wider than the seat might the addition of both arm rests be problematic. I'm a "wide body" at 270 lbs. and I was not hampered in any way -- the opening between both arm rests when installed is almost a couple of inches wider than the seat itself. Next time I shower, I'll take my camera and shoot a couple of photos. IMHO, at least one arm rest should be included as a standard item. Made it a whole lot easier for me to sit and stand between the bench and my walker by providing something to grab onto while descending and to push up on when rising, and also helped a lot with the slight lift needed to lock the seat in the outside position as noted above.

I purchased this transfer bench for my mom and she has been it for about 3 weeks. She is very pleased with the ease of use and most of all, allowing her to bathe safely without assistance.Assembly is very easy, no tools needed. The weight is about 18 pounds and the box is approximately 29" x 17" x 9". The horizontal bars go through the seat bottom which comes attached to the rotational hardware. The seat back and legs are easily attached. I forgot how the mounting bracket attaches to the seat or if it came already attached. The legs are adjustable and the large rubber feet are angled to fit the slight slope of the bottom of the tub.The mounting bracket saves a bit of floor space over the model with 4 legs (2 legs inside tub, 2 outside.) The Velcro strap isn't needed at this time but there isn't a way to remove it without disassembling the rotational hardware or cutting it off. It is very securely in place and may be needed in the future. To keep it out of the way, it is wrapped behind the back of the seat.There are red tabs on the left and right side of the seat. When a red tab is pressed, it pushes the spring button through a hole in the tubing and allows the seat to slide to the left or right. There is a red lever in the center that is pressed to release the rotational lock. When the seat is rotated 90 degrees from the position in the photo, there is a support bar which is part of the frame. An accessory handle that attaches to the side of the seat (item 31780) is available but my mom has not found it necessary to purchase one.The max. tub wall width specification is 5.75" so I was concerned about the mounting bracket being too small because of contours on the outer side of her 5.75" wide tub wall, making it difficult to get an exact width measurement. The bracket is made of two pieces and the screw adjustment allows expansion to about 6.25". With the included adhesive rubber grip pads (about 1/8" thick) that you apply to the under sides of the bracket, it barely fits over the tub wall but you can still slide it along the tub wall it can still be tightened securely.The x-short seat is 16" wide and because of the wide tub wall, the right edge of the seat is only about 0.5" from the inside edge of the tub when the seat is rotated and locked in place (in the product photo, the seat would be rotated 90 degrees counterclockwise and facing the right side of the tub.) I might buy a curved shower curtain rod so there is more space between the seat and shower curtain. If we had purchased the regular size bench with approximate 20" wide seat, I think the right edge of the seat would be over the top of the tub wall when rotated and locked in place so water might flow over the edge of the tub and onto the floor. I don't think seat width would be an issue if the tub wall was thinner. Since my mom is small, the x-short bench works out very well in the small 29" of space between the bathroom wall and the toilet, the only position where this transfer bench can be located.In 3 weeks, there haven't been any problems with assembly or use of this product and it makes my mom's life much easier. It is also safer for my dad to sit in the shower, reducing the risk of falling and possible injuries. I wish I had purchased this transfer bench a long time ago.

Not easy to reach chair controls. Not real easy to slid without assistance.

Perfect size. Very stable and operated perfectly. I would recommend it, and will buy it for additional baths.