MO2016 All-in-One 3D Printer Adhesive Glue - ABS, PLA, PETG, HIPS, and TPU Flex Filament on Glass, Flex Plate, PEI, Buildtak, Kapton - 3D Printing Accessories, Supplies, and Materials (50mL)

Stuff is no joke... it sticks.Better for Smooth Glass Plates than Textured PEI Plates, imo.Used it with the Textured PEI plate...Almost hard to get the print off the plate because the textured plate almost doesn't even need glue to begin with.Worked with PETG and PLA.Leaves a half-sticky film that washes right off...Doesn't smell like chemical or leave an odor on the model after you rinse it with water.It's more of a Thin Paste than a Liquid.The first stuff that came with the printer was more of a liquid that held well, but didn't hold as tight.I still havn't had any models unseat from the plate while printing with either glue.

This magigoo makes a huge difference in making sure my prints stay stuck to the build plate. Just use the included wipe nozzle to spread a thin layer on the build plate, and viola you're ready to print!A word of caution if you're using this with a plate that leaves a micropattern, the glue will be the only part to pick up the pattern. And the glue will likely stay on your print untill you wipe it off.

I have struggled for years (15years) with prints not sticking. Changed first layer, put down blue tape, used glue stick - nothing worked. Followed the information on the website - applied a layer to my Anycubic Kobra 3 and NO PROBLEMS SINCE. Got to order another bottle ( my first one is 90% full) just in case there is a problem in getting more.The BEST thing since auto bed leveling.

This glue is fantastic! I run a small business on Etsy so I 3D print almost every day and you honestly don't need to reapply the glue between every print. I would say every other print and sometimes more. Easy removal too, just bend the plate a little bit and the item pops right off. I own a Flashforge Adventure 5M and it works perfect. When you apply it also does not dispense a lot, a little goes a long way. This glue is way better than the glue that my 3D printer came with. Highly recommend!

Fairly new to 3D printing, so I don’t have the most experience with different glues. For the price and what you get, seems a little a steep. Tried printing Bambu labs filament with a 0.2mm nozzle on a smooth plate using this glue, I wasn’t able to get the print to succeed. Glue seemed to work well on the textured plate, although the textured plate usually does well anyway. I may purchase another bottle after my current one gets used up, but I will probably explore around to see if there are other brands/types that adhere better and provide better quality prints.

Excellent product! Had prints coming up off of the bed and stick glue just was not cutting it. This product was perfect for the bed adhesion that i needed. No more prints coming up off of the bed and perfect first layers!

I've been using Magigoo for about 3 months, my printer runs almost non-stop and I can say without reservation, this stuff works splendidly. I've only tested it using PLA, PLA+, and PETG so far. Hopefully it will work just as well with TPU and ABS.A couple of things I've learned along the way:1. Be careful you don't squeeze the bottle too much, or the applicator cap will pop off the bottle and you'll have this stuff everywhere. I shake the bottle really well, place the applicator on the bedplate and push gently to get the goo to flow to the pad on the tip. You only need to do this occasionally as a little goes a long way. If necessary I will GENTLY squeeze the bottle, but only if the applicator is firmly against the bedplate. I haven't experienced a bottle blow-out as others have described but I can see how this could easily happen. Use care and you won't have a mess on your hands!2. At first I was cleaning the surface with warm water after every print, but it wasted a lot of product. Start with a clean, dry bedplate, wipe it down with isopropyl alcohol (optionally, just makes sure the surface is oil-free), and apply the product in a uniform manner. Don't worry if you have overlaps and bubbles - once the product dries it actually aids adhesion and won't make a significant impact on your print. Once I've coated the bedplate for the first time, I'll let it air-dry and then apply a second layer going at right angles to the first, and then kick on the bed heater to set the product well.3. WAIT FOR THE BEDPLATE TO COOL DOWN before you remove the print! I wait for the plate to cool to at least 40 degrees C before prying the print from the plate. This will make it much easier to remove the print and it lessens the "damage" to the adhesive's layer. Some of the product will adhere to the printed parts, this washes off with warm water without problems.4. I use a razorblade scraper to gently pry the printed parts from the plate, trying not to scrape the adhesive off the plate as much as possible. You will see marks on the plate where the print came off - this is great because it means the adhesive worked!5. I spot touch-up the marks from the previous prints, and I've found that multiple layers of the product seem to work better and need less touching up over time. You don't need to wait for the bedplate to cool to room temp before reapplying the product in small areas, it just dries more quickly. The main thing is don't be in a hurry to wash the bedplate and reapply - it wastes the product and is not needed. Like I said above, multiple layers work better that just one. I've been printing for days with just touching up spots and it's been holding my parts to the plate like a lioness holding her cubs :-)I like this product because it's relatively inexpensive, it has no odor (not to me anyway), it's easy to apply and touch up, and washes off the bedplate and printed parts with warm water. On one occasion, the printed part was a large, flat plate and in that case I removed the print in the sink with warm water. It was stuck so well I was afraid I'd break the print or the glass bedplate, but under a little warm water the print just slid right off.If you use these techniques I've discovered that one small bottle with last for quite a while.

work as advertised